Replacing uPVC Window Handles
Changing upvc window handles is a fairly straightforward job. It is essential to ensure that the replacement handle fits inside the spindle cutout of the window mechanism.
If the steps below are followed correctly If you follow the steps correctly, any cockspur handle can be able to fit into most windows. The step height of the handle is crucial.
What to Look For
Over time, uPVC handles on many windows in the UK begin to show signs of wear and tear. If this occurs, the window handle could become shaky or difficult to operate, making it necessary to replace it. Anyone who is comfortable with basic hand tools can complete this relatively simple task.
The first step is to make sure that the handle is securely attached to the frame of the window and in the open position. The next step is to locate the pins or screws which hold the handle in place. They are usually on the inside of the handle. They can be removed using an screwdriver or pliers.
Once the handle has become loose and sagging, gently pull it back from its hinges. Then, you'll need to find a new handle in the same style and size. This can be done in the DIY store or on the internet. The process should take only five minutes and requires a screwdriver.
When replacing the handle of a uPVC handle It is crucial to take into consideration the step height. This is the distance from the bottom of the handle to the point at which it rests on the frame of the window. This is typically an accepted measurement, however it is important to determine the step height of your current handle prior to ordering the new one.
Depending on the kind of handle you choose, there are different sizes available. Inline handles for uPVC windows usually feature lug centers of 31mm, and there are also varieties of cockspur handles with 43mm centres. Tilt and turn handles are often found on windows made of uPVC and they feature a specific design that allows the window to be tilted in for ventilation and turned to fully open the window.
The most common cause of breakage in uPVC handles is that they crack internally instead of breaking off from the base section. This makes them difficult to open and therefore it is crucial to ensure that the replacement handle you buy has the same spindle length that your current one.
Remove the old handle
If the handles on your windows are damaged or not properly fitted, they can cause double-glazed windows to open and close incorrectly. They may even get stuck. This could be due to a number of factors, including general wear and tear on the handle or corrosion. In these cases, it is important to find replacement window handles made of upvc as soon as you can to avoid further damage and loss of functionality.
When replacing upvc windows handles and handles, it is important to remove the old handles from the window. Begin by removing the screw when the handle in closed position. Once you have removed that screw, you are able to remove the handle. You can make the process easier by using an electronic screwdriver.
It is also important to note that the handles' screws could be hidden behind plastic caps, therefore it is a good idea to take a Stanley knife to the screws and take them off. After you have removed the old handle, you'll have to examine the square cutout on the base to ensure that the new handle for the window lock is compatible. It is essential to measure the spindle length on the handle you used to replace it with and then compare it with the size of the window mechanism spindle cutout.
There are three kinds of upvc handles: Espag handles with a central screw that can be turned left or right, Cranked handles with two screws and Spade handles, which are made of flat arms and can be used on either side of the window made of upvc. Once you have a suitable replacement, it's just a matter of screwing the handle into place and making sure that the spindle is correctly fitted into the lock mechanism. Once that is done the handle should be secured to the window frame, and your new upvc window handles should be secure.
Take a measurement of the Spindle
If you have to replace a Upvc handle that has fallen, it's likely that the spindle that holds it in place is damaged or loose. In some cases this can be fixed with screws or pins to secure it. In other cases it will need to be replaced entirely. There are a few different types of upvc window handles . There are three kinds of handles: inline espagnolette tilt-and-turn, and cockspur. Each type of handle is installed and replaced in a different manner.
It is essential to measure the current handle prior to purchasing an alternative. This will ensure that the handle fits the window correctly and will be of the correct size. All handles are sized in accordance with industry standards, making it easy to identify the correct size.
To determine the size of your handle first, take it out of the window by turning it to an open position. You should be able to determine the size of the screw or pin that holds the handle. Then, use a ruler or tape measure to determine the length of the spindle. Once you have determined the length of the spindle you can purchase a new spindle that is the same length.
The step height of a window handle is also important to consider when you are buying replacements. The step height is measured from the base to the point at which the handle is positioned on the frame. In general, this is approximately 21mm for uPVC windows or 9mm for aluminum. To make sure that the new handle will fit the gap, drop something in the gap to determine the distance it will go before it meets an obstruction.
Cockspur handles may have different backsets depending on what style of window you install them in. Inline Espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles have different backsets depending on the window they are in. This is because they feature a spur that extends from the handle and then locks over the cockspur wedge striker plate.
Install the new handle
When you've picked a new handle, ensure that it is aligned with the screw holes on the door and fix it using the screws provided. If you're replacing the latch lever it can be put in similarly to the main door handle. After that, attach the door trim again to hide the mounting screws.
Tips: To take the head made of metal from the wedge of wood make sure the handle is held so that its wider end is resting on the floor. Use a hammer to tap the thin end of the handle. Be careful not to scratch the handle or the spindle.